TOA
The N-8000MI is a multisource interface for the N-8000 intercom system. When used as an analog audio bridge to the N-8000 intercom system, it accepts two line-level inputs which can be broadcast to any paging zone or station on the system. Two line-level outputs are provided, with sixteen contact closure inputs and sixteen relay outputs. Contact closures may be synchronized with a paging event, linked to contact closure inputs, be triggered by a station call, be triggered by IP control or a master station, or be triggered by a fault in the network or a 2-wire (N-8000EX/N-8010EX) line fault for 24/7 supervision. Rack mount and wall mount hardware included
table id="spectable">with a semi-fixed volume for adjustment (0 to -25 dB)
Control: 2 inputs (2 P/input), no-voltage make contact input, open voltage: 12 V DC,
short-circuit current: 10 mA
Removable terminal block (8 pins)
Control: 2 outputs (2 P/output), relay contact output, contact capacity: 24 V DC/0.5 A
Removable terminal block (8 pins)
short-circuit current: 10 mA, removable terminal block (18 pins)
removable terminal block (18 pins)
600 Ω, balanced, mini-clamp connector (2 pins),
with adjustment functions for both input and output
(Input: 0 to 15 dB, Output: -15 to 0 dB), Analog E & M interface
600 Ω, balanced, mini-clamp connector (2 pins)
Signal method: EXES-2000/EXES-6000 tie-line method
Selective signal: DTMF signal
Network protocol: TCP/IP, UDP, HTTP, RTP, ARP, ICMP, IGMP
Audio packet transmission system: Unicast, Multicast
Number of paging destinations: Unicast (max. 16), Multicast (max. 191)
Connector: RJ45 connector
Voice sampling frequency: 16 kHz, 8 kHz (controllable on the software)
Quantifying bit number: 16-bit
Voice encoding method: Sub-band ADPCM, Cryptosystem
Voice packet loss recovery: Silence insertion
Audio delay time: 80 ms, 320 ms (controllable on the software)
Time of day hold facility, Reset switch (front panel)
Mini-clamp plug (2 pins) …10, Removable terminal plug (8 pins) …2,
Removable terminal plug (9 pins) …4, Plastic foot …4, Screw for fitting plastic foot …4,
Rack mounting bracket …2, Screw for rack mounting …4, Wall mounting bracket …2,
Screw for mounting bracket …8, Screw for wall mounting …4
The N-8000DI is a Direct select unit designed for use with TOA's packet intercom system (IP network-compatible intercom system) that employs the packet audio technology. It is equipped with each 32 contact inputs and outputs, and the indicators on the front panel indicate the output statuses. Connecting the unit to the LAN permits the calling station display, external equipment control, and direct selection function to be realized. It can be mounted in an EIA equipment rack (1U size) with the use of an accessory rack mounting bracket or installed on a wall using an optional wall mounting bracket. Rack mount and wall mount hardware included.
| Power Source | 120 V AC, 50/60 Hz |
|---|---|
| Power Consumption | 16 W (max.) |
| Contact Input | 32 inputs, no-voltage make contact input, open voltage: 24 V DC, short-circuit current: 5 mA or less, removable terminal block (20 pins) (1 common terminal for 4 inputs) |
| Contact Output | 32 outputs, relay contact output, contact capacity: 24 V DC/2 - 500 mA, removable terminal block (32 pins) |
| Network Section | Network I/F: 10BASE-T/100BASE-TX (Automatic-Negotiation) Network protocol: TCP/IP, UDP, HTTP, RTP, ARP, ICMP, IGMP Connector: RJ45 connector |
| Indication | Network LNK/ACT indication, Status lamp, Power-on indication lamp, Channel indication lamps (32 channels) |
| Other | Firmware update function, System data hold function, Time of day hold facility, Reset switch (front panel) |
| Setting Method | Rack, Desk, Surface mount |
| Operating Temperature | 0 ℃ to 40 ℃ (32 ゜F to 104 ゜F) |
| Operating Humidity | 90 %RH or less (no condensation) |
| Finish | Pre-coated steel plate, black, 30 % gloss |
| Dimensions | 420 (W) × 44.3 (H) × 267 (D) mm (16.54" × 1.74" × 10.51") |
| Weight | 2.8 kg (6.17 lb) |
| Accessory | Power cord (2 m (6.56 ft)) …1, CD (for PC setting, maintenance use) …1, Removable terminal plug (10 pins) …4, Removable terminal plug (16 pins) …4, Plastic foot …4, Screw for fitting plastic foot …4, Rack mounting bracket …2, Screw for mounting bracket …8, Screw for rack mounting …4 |
| Option | Wall mounting bracket: YC-850 |
The N-8000CO is a C/O interface unit designed for use with TOA's packet intercom system (IP network-compatible intercom system) that employs the packet audio technology. It has an analog central office line circuit, allowing the intercom station to make and receive calls to and from the telephone line. Connecting the unit to the LAN permits paging calls through analog subscriber line to be made and the equipment connected to the N-8000MI and N-8000DI to be controlled. It can be mounted in an EIA equipment rack (1U size) with the use of an optional rack mounting bracket or installed on a wall using an optional wall mounting bracket. Rack mount kit not included. Use TOA MB-15B-BK (one unit per rack space) or MB-15B-J (two units per rack space)
| Power Source | 120 V AC, 50/60 Hz |
|---|---|
| Power Consumption | 7 W (max.) |
| C/O Interface | Public Switched telephone networks Number of lines: 1 line Selective signal type: DTMF signal Signal system: Compatible with loop start signaling Wiring method: 1 pair of twisted pair cables |
| Network Section | Network I/F: 10BASE-T/100BASE-TX (Automatic-Negotiation) Network protocol: TCP/IP, UDP, HTTP, RTP, ARP, ICMP, IGMP Audio packet transmission system: Unicast, Multicast Number of paging destinations: Unicast (max. 8), Multicast (max. 191) Connector: RJ45 connector Voice sampling frequency: 16 kHz, 8 kHz (controllable on the software) Quantifying bit number: 16-bit Voice encoding method: Sub-band ADPCM, Cryptosystem Voice packet loss recovery: Silence insertion Audio delay time: 80 ms, 320 ms (controllable on the software) |
| Indication | Network LNK/ACT indication, Status lamp, Power-on indication lamp, Line in-use lamp |
| Other | Firmware update function, System data hold function, Time of day hold facility, Reset switch (front panel) |
| Setting Method | Rack, Desk, Surface mount |
| Operating Temperature | 0 ℃ to 40 ℃ (32 ゜F to 104 ゜F) |
| Operating Humidity | 90 %RH or less (no condensation) |
| Finish | Pre-coated steel plate, black, 30 % gloss |
| Dimensions | 210 (W) × 44.3 (H) × 267 (D) mm (8.27" × 1.74" × 10.51") |
| Weight | 1.7 kg (3.75 lb) |
| Accessory | Power cord (2 m (6.56 ft)) …1, CD (for PC setting, maintenance use) …1, Mini-clamp plug (2 pins) …2, Plastic foot …4, Screw for fitting plastic foot …4 |
| Option | Rack mounting bracket: MB-15B-BK (for rack mounting one N-8000CO unit) MB-15B-J (for rack mounting two N-8000CO units) Wall mounting bracket: YC-850 |
The N-8000AF provides either an analog audio input/output bridge to the N-8000 system, a bell schedule generator with internal tones, or record functionality for archival purposes. It can also function as the system master clock, with sync to contact closure or NTP server as required. When used as an analog audio bridge to the N-8000 intercom system, it accepts one mic or line level input which can be broadcast to any paging zone or station on the system. One line-level output is provided, with eight contact closure inputs and eight contact closure outputs. Contact closures may be synchronized with a paging event. When used as a bell schedule generator, the N-8000AF provides 16 schedules with 64 events per schedule. Five internal tones are available, with the option to trigger up to four external paging sources. When used as for recording it provides an analog audio output and contact closure control for external recording devices to record pages, announcements, and conversations. Rack mount kit not included. Use TOA MB-15B-BK (one unit per rack space) or MB-15B-J (two units per rack space).
| Power Source | 120 V AC, 50/60 Hz |
|---|---|
| Power Consumption | 7 W (max.) |
| Audio Input | 1 input (transformer isolated), -58 dB* to 0 dB*, 2 kΩ, balanced (MIC/LINE input, controllable on the software) with input volume control knob, removable terminal block (3 pins) |
| Audio Output | 1 output (transformer isolated), 0 dB*, 600 Ω, balanced, removable terminal block (3 pins) |
| Contact Input | 8 inputs, no-voltage make contact input, open voltage: 24 V DC, short-circuit current: 5 mA or less, removable terminal block (10 pins), (1 common terminal for 4 inputs) |
| Contact Output | 8 outputs, relay contact output, contact capacity: 24 V DC/2 - 500 mA, removable terminal block (16 pins) |
| Time Sync Input | 1 input, no-voltage make contact input, open voltage: 24 V DC, short-circuit current: 5 mA or less, removable terminal block (2 pins) |
| Network Section | Network I/F: 10BASE-T/100BASE-TX (Automatic-Negotiation) Network protocol: TCP/IP, UDP, HTTP, RTP, ARP, ICMP, IGMP Audio packet transmission system: Unicast, Multicast Number of paging destinations: Unicast (max. 8), Multicast (max. 191) Connector: RJ45 connector Voice sampling frequency: 16 kHz, 8 kHz (controllable on the software) Quantifying bit number: 16-bit Voice encoding method: Sub-band ADPCM, Cryptosystem Voice packet loss recovery: Silence insertion Audio delay time: 80 ms, 320 ms (controllable on the software) |
| Indication | Network LNK/ACT indication, Status lamp, Power-on indication lamp, Signal lamp, Peak lamp |
| Other | Firmware update function, System data hold function, Time of day hold facility, Reset switch (front panel) |
| Setting Method | Rack, Desk, Surface mount |
| Operating Temperature | 0 ℃ to 40 ℃ (32 ゜F to 104 ゜F) |
| Operating Humidity | 90 %RH or less (no condensation) |
| Finish | Pre-coated steel plate, black, 30 % gloss |
| Dimensions | 210 (W) × 44.3 (H) × 267 (D) mm (8.27" × 1.74" × 10.51") |
| Weight | 1.7 kg (3.75 lb) |
| Accessory | Power cord (2 m (6.56 ft)) …1, CD (for PC setting, maintenance use) …1, Removable terminal plug (2 pins) …1, Removable terminal plug (3 pins) …2, Removable terminal plug (5 pins) …2, Removable terminal plug (8 pins) …2, Plastic foot…4, Screw for fitting plastic foot …4 |
| Option | Rack mounting bracket: MB-15B-BK (for rack mounting one N-8000AF unit) MB-15B-J (for rack mounting two N-8000AF units) Wall mounting bracket: YC-850 |
The N-8000RS Substation Interface Unit uses packet audio technology to permit connection of up to 16 RS-1xx series call switches or door stations. Call switches and door stations use the same shielded twisted pair wiring. Each port provides 1W @25V to a door station, or 25V loudspeaker attached to a call switch. Each N-8000RS supports 2 voice links. The N-8000RS requires an IP master station, or connection to a 2-wire or 4-wire Exchange with at least one master station on the exchange.
The N-8010EX IP Intercom Exchange uses packet audio technology to permit connection of up to 16 N-8000 series 2-wire master or door stations. Master stations and door stations use the same unshielded twisted pair wiring. Each N-8010EX supports one voice link. The N-8010EX supports the audio trigger function. The exchange may be used as a stand-alone system (requires at least one master station) or connected to an N-8000 IP intercom system over LAN or WAN. Rack mount and wall mount hardware are included
The latest software version is 4.2.2 (update:2020/6/18), with previous versions 4.2.0(update:2015/04/03), 4.10(update:2014/11/13),and 1.41(update:2008/10/06). The Maintenance Software(Ver.1.2.0) is used to monitor or maintain equipment within the system(upload:2015/04/03).
| Power Source | 120 V AC, 50/60 Hz |
|---|---|
| Power Consumption | 35 W (at rated), 45 W (max.) |
| Interface Section for Sub-station | Number of lines: 16 lines Number of speech link: 2 links Transmission system: Analog baseband Transmission range: 500 m (546.81 yd)/φ0.5 mm (AWG24), 800 m (874.89 yd)/ Speech method: Half-duplex conversation by way of voice switch Connector: Removable terminal block (3 pins) Wiring method: Two-core shielded cable Audio output: Max. 1 W/line (conversation), Max. 0.5 W/line (paging) Feeding voltage/current: 22 V DC, 30 mA max. Control signal: Call in button detection, privacy button detection, hook detection |
| Network Section | Network I/F: 10BASE-T/100BASE-TX (Automatic-Negotiation) Network protocol: TCP/IP, UDP, HTTP, RTP, ARP, ICMP, IGMP Audio packet transmission system: Unicast, Multicast Number of paging destinations: 0, *Reception only Connector: RJ45 connector Voice sampling frequency: 16 kHz, 8 kHz (controllable on the software) Quantifying bit number: 16-bit Voice encoding method: Sub-band ADPCM, Cryptosystem Voice packet loss recovery: Silence insertion Audio delay time: 80 ms, 320 ms (controllable on the software) |
| Indication | Network LNK/ACT indication, Status lamp, Power-on indication lamp |
| Other | Firmware update function, System data hold function, Reset switch (front panel), Forced air cooling |
| Setting Method | Rack, Desk, Surface mount |
| Operating Temperature | 0 ℃ to 40 ℃ (32 ゜F to 104 ゜F) |
| Operating Humidity | 90 %RH or less (no condensation) |
| Finish | Pre-coated steel plate, black, 30 % gloss |
| Dimensions | 420 (W) × 44.3 (H) × 325.5 (D) mm (16.54" × 1.74" × 12.81") |
| Weight | 3.9 kg (8.6 lb) |
| Accessory | Power cord (2 m (6.56 ft)) …1, CD (for PC setting, maintenance use) …1, Removable terminal plug (3 pins) …16, Plastic foot …4, Screw for fitting plastic foot …4, Rack mounting bracket …2, Screw for mounting bracket …8, Screw for rack mounting …4 |
| Option | Wall mounting bracket: YC-850 |
The N-8650DS is an indoor IP door station with a separate microphone and speaker, allowing full duplex conversations with Master Stations. The N-8650DS is equipped with one control input and five control outputs (1 relay and 4 open collector) for integration with security or other 3rd party systems. An external speaker output provides .5W @8Ω. External or internal speaker priority is programmable. The N-8650DS may be powered by PoE (recommended).
| Power Source | Power supply device that complies with IEEE802.3af standard or 12 V DC (supplied from the AC adapter (option)) |
|---|---|
| Power Consumption | Use of the AC adapter (12 V DC): 3.5 W (station only), Use of the PoE (48 V DC): 5 W |
| Speech Method | Hands-free conversation |
| Audio Frequency Range | 300 Hz - 7 kHz |
| Hands-free | Speaker: 3.5 cm (1.38") cone-type, maximum output 0.5 W, 8 Ω Microphone: Omni-directional electret condenser microphone |
| Contact Input | 1 channel, no-voltage make contact input, open circuit voltage: 5 V DC, short circuit current: 10 mA or less, unterminated ends |
| Contact output | Open collector output, 4 channels, withstand voltage: 30 V DC, control current: Max. 50 mA (4 output 1COMMON), unterminated ends Relay contact output, 1 channel, withstand voltage: 30 V DC, control current: Max. 500 mA, unterminated ends |
| External Speaker Terminal | Maximum output 0.5 W, 8 Ω, unterminated ends |
| Network Section | Network I/F: 10BASE-T/100BASE-TX (Automatic-Negotiation) Network protocol: TCP/IP, UDP, HTTP, RTP, ARP, ICMP, IGMP Audio packet transmission system: Unicast, Multicast Number of paging destinations: 0, *Reception only Connector: LAN: RJ45 connector (PoE compatible) Voice sampling frequency: 16 kHz, 8 kHz (controllable on the software) Quantifying bit number: 16-bit Voice encoding method: Sub-band ADPCM, Cryptosystem Voice packet loss recovery: Silence insertion Audio delay time: 80 ms, 320 ms (controllable on the software) |
| Indication | Status lamp (built in the Call button) |
| Installation Method | Flush-mount/Surface-mount |
| Operating Temperature | -10 ℃ to 50 ℃ (14 ゜F to 122 ゜F) |
| Operating Humidity | 90 %RH or less (no condensation) |
| Finish | ABS resin, dark gray |
| Dimensions | 117.2 (W) × 162 (H) × 60 (D) mm (4.61" × 6.38" × 2.36") |
| Weight | 400 g (0.88 lb) |
| Accessory | Box mounting screw (No.6-32UNC × 20) …4, Box mounting screw (M4 × 20) …4, LAN coupler …1 |
| Option | AC adapter: AD-1210P, AD-1215P |
| Applicable Box | For wall mount: Wall-mount Box YS-13A (option) For flush mount: 3-gang electrical box or Back Box YC-150 (option) |
The N-8000EX IP Intercom Exchange uses packet audio technology to permit connection of up to 16 N-8000 series 2-wire master or door stations. Master stations and door stations use the same unshielded twisted pair wiring. Each N-8000EX supports up to 8 external voice links and 4 internal voice links. The N-8000EX supports the audio trigger function. The N-8000EX includes two balanced line level analog audio output channels and two relay outputs. The exchange may be used as a stand-alone system (requires at least one master station) or connected to an N-8000 IP intercom system over LAN or WAN.
| Power Source | 120 V AC, 50/60 Hz |
|---|---|
| Power Consumption | 50 W (at rated), 75 W (max.) |
| Interface Section for station | Number of lines: 16 lines Number of speech link: Internal: 4/External: 8 Type of Speech Path: Space sharing/Time Space sharing Transmission system: 2 wire 160 kbps echo canceller transmission system Signal Level: 0 dB* or less Transmission range: Max. 1500 m (φ0.65 mm, Loop resistance 170 Ω) Speech method: Simultaneous conversation by way of echo canceller (Hands-free), Connector: Dedicated connector Wiring method: 1 set of twisted pair cable Feeding voltage/current: 48 V DC, Max. 70 mA |
| Paging Output | Audio: 2 channels Max. 0 dB*, 600 Ω, balanced Control: 2 channels, relay contact output, contact capacity: 24 V DC/0.5 A Connector: Removable terminal block |
| Network Section | Network I/F: 10BASE-T/100BASE-TX (Automatic-Negotiation) Network protocol: TCP/IP, UDP, HTTP, RTP, ARP, ICMP, IGMP Audio packet transmission system: Unicast, Multicast Number of paging destinations: Unicast (max. 16), Multicast (max. 191) Connector: RJ45 connector Voice sampling frequency: 16 kHz, 8 kHz (controllable on the software) Quantifying bit number: 16-bit Voice encoding method: Sub-band ADPCM, Cryptosystem Voice packet loss recovery: Silence insertion Audio delay time: 80 ms, 320 ms (controllable on the software) |
| Indication | Network LNK/ACT indication, Status lamp, Power-on indication lamp |
| Other | Firmware update function, System data hold function, Reset switch (front panel) Forced air cooling, Time of day hold facility |
| Installation Method | Rack, Desk, Surface mount |
| Operating Temperature | 0 ℃ to 40 ℃ |
| Operating Humidity | 90 %RH or less (no condensation) |
| Finish | Pre-coated steel plate, black, 30 % gloss |
| Dimensions | 420 (W) x 44.3 (H) x 356 (D) mm |
| Weight | 4.1 kg |
| Accessory | AC power cord (2 m) …1, CD (for PC setting, maintenance use) …1, Removable terminal plug (4 pins)…2, Mini-clamp plug (2 pins) …20, Plastic foot …4, Screw for fitting plastic foot …4, Rack mounting bracket …2, Screw for rack mounting …4, Wall mounting bracket …2, Screw for mounting bracket …8, Screw for wall mounting …4 |
The N-8640DS is an IP65, impact resistant IP door station with a separate microphone and speaker, allowing full duplex conversations with Master Stations. The N-8640DS is equipped with one control input and five control outputs (1 relay and 4 open collector) for integration with security or other 3rd party systems. An external speaker output provides .5W @8Ω. External or internal speaker priority is programmable. The N-8640DS may be powered by PoE (recommended).
The N-8010RS Substation Interface Unit uses packet audio technology to permit connection of up to 16 RS-1xx series call switches or door stations. Call switches and door stations use the same shielded twisted pair wiring. Each port provides 1W @25v to a door station, or 25V loudspeaker attached to a call switch. Each N-8010RS supports 1 voice link. The N-8000RS requires an IP master station, or connection to a 2-wire or 4-wire Exchange with at least one master station on the exchange.
| Power Source | 120 V AC, 50/60 Hz |
|---|---|
| Power Consumption | 26 W (at rated), 32 W (max.) |
| Interface Section for Sub-station | Number of lines: 16 lines Number of speech link: 1 link Transmission system: Analog baseband Transmission range: 500 m (546.81 yd)/φ0.5 mm (AWG24), 800 m (874.89 yd)/ Speech method: Half-duplex conversation by way of voice switch Connector: Removable terminal block (3 pins) Wiring method: Two-core shielded cable Audio output: Max. 1 W/line (conversation), Max. 0.5 W/line (paging) Feeding voltage/current: 22 V DC, 30 mA max. Control signal: Call in button detection, privacy button detection, hook detection |
| Network Section | Network I/F: 10BASE-T/100BASE-TX (Automatic-Negotiation) Network protocol: TCP/IP, UDP, HTTP, RTP, ARP, ICMP, IGMP Audio packet transmission system: Unicast, Multicast Number of paging destinations: 0, *Reception only Connector: RJ45 connector Voice sampling frequency: 16 kHz, 8 kHz (controllable on the software) Quantifying bit number: 16-bit Voice encoding method: Sub-band ADPCM, Cryptosystem Voice packet loss recovery: Silence insertion Audio delay time: 80 ms, 320 ms (controllable on the software) |
| Indication | Network LNK/ACT indication, Status lamp, Power-on indication lamp |
| Other | Firmware update function, System data hold function, Reset switch (front panel), Forced air cooling |
| Setting Method | Rack, Desk, Surface mount |
| Operating Temperature | 0 ℃ to 40 ℃ (32 ゜F to 104 ゜F) |
| Operating Humidity | 90 %RH or less (no condensation) |
| Finish | Pre-coated steel plate, black, 30 % gloss |
| Dimensions | 420 (W) × 44.3 (H) × 325.5 (D) mm (16.54" × 1.74" × 12.81") |
| Weight | 3.8 kg (8.38 lb) |
| Accessory | Power cord (2 m (6.56 ft)) …1, CD (for PC setting, maintenance use) …1, Removable terminal plug (3 pins) …16, Plastic foot …4, Screw for fitting plastic foot …4, Rack mounting bracket …2, Screw for mounting bracket …8, Screw for rack mounting …4 |
| Option | Wall mounting bracket: YC-850 |
The N-8610RM Remote Master Station is an IP remote microphone station that employs packet audio technology. High quality voice output is broadcast to N-8000 intercom door and master stations or to paging amplifiers using one of the IP to analog audio outputs available on the N-8000AF, N-8000MI or N-8000EX. 14 pre-programmed buttons provide access to stations, paging zones, one-touch dialing, 10-key and Function key. The N-8610RM may be expanded to 54 buttons using multiple RM-210 Extensions. The N-8610RM may be powered by PoE or an optional AD-1215 power supply. When using PoE with RM-210s, make sure that the available PoE can accommodate a minimum of 7.5 W on one port
| Power Source | Power supply device that complies with IEEE802.3af standard or 12 V DC (supplied from the AC adapter (option)) |
|---|---|
| Power Consumption | Use of the AC adapter (12 V DC): 4 W (microphone only), 8.5 W (when connecting 4 RM-210 Extension units) Use of the PoE (48 V DC): 5.2 W (microphone only) 7.5 W (when connecting 4 RM-210) |
| Speech Method | Hands-free or handset conversation (use of goose-neck microphone) |
| Audio Frequency Range | 300 Hz - 7 kHz |
| Microphone | Unidirectional electret condenser microphone |
| Built-in Speaker | 6.6 cm (2.6") cone-type, rated output 0.3 W, 8 Ω |
| Network Section | Network I/F: 10BASE-T/100BASE-TX (Automatic-Negotiation) Network protocol: TCP/IP, UDP, HTTP, RTP, ARP, ICMP, IGMP Audio packet transmission system: Unicast, Multicast Number of paging destinations: Unicast (max. 16), Multicast (max. 191) Connector: LAN: RJ45 connector (PoE compatible) Voice sampling frequency: 16 kHz, 8 kHz (controllable on the software) Quantifying bit number: 16-bit Voice encoding method: Sub-band ADPCM, Cryptosystem Voice packet loss recovery: Silence insertion Audio delay time: 80 ms, 320 ms (controllable on the software) |
| No. of Connectable Expansion | Max. 4 units (maximum 2 units at P0E power supply) |
| Operation | Function keys (including a covered key), talk key |
| Indicator | Power indicator, Status indicator, Selection indicator, Broadcast status indicator, Microphone indicator |
| Installation Method | Desk/Surface mounted master station (When mounting to the wall, use the optional WB-RM200) |
| Operating Temperature | 0 ℃ to 40 ℃ (32 ゜F to 104 ゜F) |
| Operating Humidity | 90 %RH or less (no condensation) |
| Finish | ABS resin, blueish gray |
| Dimensions | 190 (W) × 76.5 (H) × 215 (D) mm (7.48 × 3.01" × 8.46")" (excluding microphone) |
| Weight | 700 g (1.54 lb) |
| Accessory | CD (for PC setting, maintenance use) …1, Ferrite clamp (for power supply cable, LAN cable, and extension unit cable) x 1 each |
| Option |
Remote microphone extension: RM-210, Wall mounting bracket: WB-RM200, AC adapter: AD-1215P |
The N-8600MS is the IP Master Station for the N-8000 system. The LCD screen shows incoming calls which may be selected at random (Selective Mode) or in the order received (Sequential Mode). Calls may be initiated based on previous connection (last 10 conversations). 3-party conference calls may be initiated from this master station. Bell schedule changes may be initiated or suspended from this master station. Speaker volume is adjustable at the station as well as in software. Hands free conversations with Full and 1/2 Duplex stations as well as PTT mode. Pages and station calls may be quickly redialed using the Redial key. Automatic connection or continuous call reception. Speed dialing, Dial Pattern, and One-touch dialing are available. Manual call transfers and Automatic call transfers (Group Hunting, Absence Transfer, Time Transfer) may be programmed using the keypad or the N-8000 Setting Software. Advanced functions may be password protected. The N-8600MS is the only master station that can communicate with the SX-2000 system, using the SX-200IP input module on the SX system. Power by PoE or optional AD-1215P
| Power Source | Power supply device that complies with IEEE802.3af standard or 12 V DC (supplied from the AC adapter (option)) |
|---|---|
| Power Consumption | Use of the AC adapter (12 V DC): 2.5 W (station only) Use of the PoE (48 V DC): 3 W |
| Speech Method | Hands-free or handset conversation |
| Audio Frequency Range | 300 Hz - 7 kHz |
| Hands-free | Speaker: 5.7 cm (2.24) cone-type Microphone: Omni-directional electret condenser microphone |
| Handset | Receive path: Dynamic type, Send path: Electret condenser microphone |
| Headset Terminal | Speaker: 150 Ω, φ3.5 mm (0.14) mini jack" Microphone: -49 dB*, φ3.5 mm (0.14) mini jack" |
| External Speaker Terminal | Maximum output 0.5 W, 8 Ω, screwless connector (2 pins) |
| Network Section | Network I/F: 10BASE-T/100BASE-TX (Automatic-Negotiation) Network protocol: TCP/IP, UDP, HTTP, RTP, ARP, ICMP, IGMP Audio packet transmission system: Unicast, Multicast Number of paging destinations: Unicast (max. 16), Multicast (max. 191) Connector: LAN: RJ45 connector (PoE compatible) Voice sampling frequency: 16 kHz, 8 kHz (controllable on the software) Quantifying bit number: 16-bit Voice encoding method: Sub-band ADPCM, Cryptosystem Voice packet loss recovery: Silence insertion Audio delay time: 80 ms, 320 ms (controllable on the software) |
| Display | LCD: Alphanumeric characters (16 characters × 2 lines) |
| Indication | Status lamp |
| Installation Method | Desk/Surface mounted master station (When mounting to the wall, use the optional YC-280.) |
| Operating Temperature | 0 ℃ to 40 ℃ (32 ゜F to 122 ゜F) |
| Operating Humidity | 90 %RH or less (no condensation) |
| Finish | Body, Handset: ABS resin, gray |
| Dimensions | 148 (W) × 208 (H) × 70.5 (D) mm (5.83 × 8.19" × 2.78")" (excluding a curl cord section) |
| Weight | 770 g (1.7 lb) |
| Accessory | CD (for PC setting, maintenance use) …1 |
| Option | Wall mounting bracket: YC-280, AC adapter: AD-1210P, AD-1215P |
Description
The IP-A1AF is a PoE-powered Audio Interface that decodes IP audio streams into analog audio signals. It equipped itself with a built-in 15 W amplifier to drive low-impedance speaker(s) and internal storage, onto which can store up to 20 audio files. Analog audio and control outputs can also be connected to an external amplifier. It supports SIP protocol for integrations with VoIP devices, and its 20 multicast ports are available for group paging operations. It can also receive broadcasts from Video Management Systems using ONVIF. Device control and further system integration is accessed through remote API (HTTP) or local control inputs.
Features
- Receive SIP audio, ONVIF and Multicast
- Local broadcast using internal audio files or local audio source
- 1 audio input (LINE/MIC selectable, phantom power On/Off)
- 8W (PoE)/15W(PoE ) built-in amplifier, 1 LINE audio output
- 2 control inputs and 1 control output
- HTTP commands (receive)
- Audio file storage (20 files, total 80MB, WAV/MP3)
- Playback programs (Repeat, Weekly Timer)
- PoE/PoE powered
Description
The IP-A1PG is a PoE-powered Gateway Unit that integrates multiple IP Audio devices by converting audio from Video Management Systems using ONVIF or SIP voice from SIP phone systems into multicast audio streaming. It can also transmit built-in sound source or input audio as multicast audio streaming. Moreover, the event broadcasting triggered by control input, scheduler or remote API (HTTP) as well as the command set that sends multiple HTTP commands simultaneously are also available.
Features
- Convert SIP audio, ONVIF, internal audio files or local audio source into Multicast streaming
- GUI calendar scheduler function (up to 2,000 settings)
- System mute function to mute all broadcasts made by every single IP-A1 series devices within the same network
- 1 local audio input (LINE/MIC selectable, phantom power On/Off)
- 4 control inputs and 1 control output
- HTTP commands (receive/send)
- Audio file storage (20 files, total 80MB, WAV/MP3)
- PoE powered
Description
The IP-A1MP is a microphone panel that is equipped with a microphone, an activation switch and a status indicator. It can be installed with a standard electrical box as surface or flush mounting. This panel can be used as a two-way conversation or an audio monitoring microphone when used in conjunction with IP-A1 series devices.
Features
- Audio accessory unit to be used in conjunction with IP-A1 series devices for having two-way
- conversations or audio monitoring
- Omni-directional electret condensor microphone
- Momentary type push switch to initiate a call
- Indicator lights during control input is being triggered
- 1 control input and 1 control output
- 1 electronically-balanced audio output (0dB, 200Ω)
- Surface or flush mounting with a standard electrical box
Description
The IP-A1PA12 is a compact 12 W amplifier which is designed to amplify audio signals received through network. It is equipped with 25 V, 70 V and 100 V speaker line outputs to drive wide range of high impedance speakers. With an external amplifier input capability, speaker(s) can be driven by internal amplifier or external amplifier by switching over. It allows integrations with IP camera systems by using ONVIF protocol, paging from IP phone systems by using SIP protocol and group broadcast by multicast streaming. Max. 20 audio files can be registered and they can be played back by control inputs or remote API (HTTP) commands.
Features
- 12W amplifier to drive 100/70/25V line speakers
- Receive SIP audio, ONVIF and Multicast
- Local broadcast using internal audio files or local audio source
- External amplifier input (100/70/25V) to share speakers between the built-in amplifer and external PA amplifier to be switched over
- 1 audio input (LINE/MIC selectable, phantom power On/Off)
- 2 control inputs, 1 control output and 1 mute control input
- HTTP commands (receive)
- Audio file storage (20 files, total 80MB, WAV/MP3)
- Playback programs (Repeat, Weekly Timer)
- PoE powered
The Q-BB-580W White Square Surface Mount Back Box is a metal case that can be attached to TOA’s IP-A1PC580S flush-mount ceiling speaker for exposed applications. The Q-BB-580W will allow the use of TOA’s IP-A1PC580S ceiling speaker in a space where a common speaker/back can combinations will not fit due to depth considerations.
Description
The IP-A1SC15 is an IP paging horn speaker to deliver clear announcements via network with 124 dB output capability powered by PoE power source. Its rugged enclosure is IP66 rated for outdoor environments. The IP-A1SC15 supports common network protocols for easy integrations with Video Management Systems and other SIP-compatible VoIP systems and devices. Group paging function is available with 20 Multicast ports for zone paging requirements. Internal sound source file storage allows storing pre-recorded messages or tones which can be played back by 2 control inputs or Remote API (HTTP).
Features
- 124dB (PoE powered) with IP66 rating for outdoor installations
- Receive SIP audio, ONVIF Audio and Multicast
- Local broadcast using internal audio files
- 8W (PoE)/15W(PoE ) built-in amplifier, 1 LINE audio output
- 2 control inputs and 1 control output
- HTTP commands (receive)
- Audio file storage (20 files, total 80MB, WAV/MP3)
- Playback programs (Repeat, Weekly Timer)
- PoE/PoE powered
Description
The IP-A1PC238 is a PoE-powered Ceiling Speaker with a built-in 8 W amplifier and internal data storage for up to 20 audio files. It supports SIP protocol for flexible integrations with VoIP devices, and its 20 multicast ports are available for group paging operations. It can also receive broadcasts from Video Management System using ONVIF. Device control and further system integration is accessed through remote API (HTTP) or local control inputs.
Features
- 16cm (6”) cone-type speaker for in-ceiling installations
- Receive SIP audio, ONVIF Audio and Multicast
- Local broadcast using internal audio files or local audio source
- 1 audio input (LINE/MIC selectable, phantom power On/Off)
- 8W built-in amplifier, 1 LINE audio output
- 2 control inputs and 1 control output
- HTTP commands (receive)
- Audio file storage (20 files, total 80MB, WAV/MP3)
- Playback programs (Repeat, Weekly Timer)
- PoE powered
Description
The IP-A1PC580S is a PoE-powered Surface mount Speaker with a built-in 8W amplifier and internal data storage for up to 20 audio files. It supports SIP protocol for flexible integrations with VoIP devices, and its 20 multicast ports are available for group paging operations. It can also receive broadcasts from Video Management System via ONVIF audio backchannel. Device control and further system integration is accessed through remote API (HTTP) or local control inputs.
Features
- 20cm (8”) dual cone-type speaker with metal construction
- Receive SIP audio, ONVIF Audio and Multicast
- Local broadcast using internal audio files or local audio source
- 1 audio input (LINE/MIC selectable, phantom power On/Off)
- 8W built-in amplifier, 1 LINE audio output
- 2 control inputs and 1 control output
- HTTP commands (receive)
- Audio file storage (20 files, total 80MB, WAV/MP3)
- Playback programs (Repeat, Weekly Timer)
- PoE powered